Service of Nissan Sunny from 1991 to 1997 release in n-14 body.
1. Maintenance instruction
2. Maintenance
3. Engines
3.1. 1,4 and 1,6 liters petrol engine
3.1.1. Types of repair of the engine without dismantle from the car
3.1.2. Dismantle and capital repairs of the engine
3.1.2.1. Specifications
3.1.2.2. Capital repairs of the engine
3.1.2.3. Diagnostics of the engine by means of the vacuum gage
3.1.2.4. The power unit from the manual transmission
3.1.2.5. The power unit with automatic transmission
3.1.2.6. Head of the block of cylinders
3.1.2.7. Head of cylinders and valves
3.1.2.8. Pistons and rods
3.1.2.9. Crankshaft
3.1.2.10. Block of cylinders
3.1.2.11. Conrod and piston group
3.1.2.12. Radical and conrod bearings
3.1.2.13. Piston rings
3.1.2.14. Launch of the engine after capital repairs
3.2. 2,0 liters petrol engine
3.3. Diesel engine
4. Cooling system
5. System of heating and ventilation
6. Fuel and exhaust system
7. System of launch of the engine
8. Coupling
9. Transmissions
10. Half shafts
11. Brakes
12. Suspension brackets and steering
13. Body
14. Electric equipment
 







3-1-2-5-silovojj-agregat-s-avtomaticheskojj-transmissiejj.html

3.1.2.5. The power unit with automatic transmission

Dismantle


Prevention

The engine can be dismantled from the car only as a part of the power unit (i.e. assembled with transmission). The power unit falls and gets from under the car. Freely to get the engine in such a way, the car needs to be lifted on height not less than 75 cm (from a floor to a front bumper) and to establish on supports.


PERFORMANCE ORDER
1. Install the car on the firm flat platform. Block back wheels, turn on the emergency brake. Lift a forward part of the car and establish on supports.
2. Remove forward wheels.
3. Unscrew screws and remove all guards of the engine.
4. Remove a cowl (see subsection 13.7).
5. Merge cooling liquid.
6. Merge oil from the check point, turn and tighten both stoppers.
7. Merge oil and remove an oil filter, clear and tighten a drain stopper.
8. Remove the battery.
9. Remove a broad tank with an arm.
10. Take off belts.
11. Remove the generator.
12. On the cars equipped with the conditioner turn off compressor bolts, take the compressor aside and fix. Not to disconnect hoses from the conditioner.
13. Remove the pump of the hydraulic booster (see subsection 12.15).
14. Remove supports of brakes, take aside and fix, without disconnecting hoses.
15. Disconnect CV JOINTS from naves.
16. Disconnect half shafts (see subsection 10.2).
17. Disconnect a cable of the choice of transfers.
18. Remove a longeron.
19. Disconnect a reception pipe of the muffler.
20. Remove a radiator with hoses and fans.
21. Disconnect the stabilizer of cross stability (see subsection 12.6).
22. On carburetor engines remove or disconnect the following details and units:

  – air filter;
  – fuel hoses;
  – cable of a butterfly valve;
  – carburetor wires;
  – hose of the vacuum amplifier, cooling system and other hoses of sensors and valves;
  – a rack of the soaking-up collector;
  – socket of the sensor of exhaust gases.
23. On injector engines perform the following operations:

  – remove an air duct of the air filter;
  – execute actions for a decompression of fuel system, disconnect fuel hoses from the case of a butterfly valve;
  – disconnect a cable of the drive of a butterfly valve;
  – disconnect conducting sockets;
  – take conducting aside from the engine.
24. Disconnect all hoses from the soaking-up collector.
25. Remove a rack of the soaking-up collector.
26. Put identification tags and disconnect hoses of a heater and hoses of the cooling system from the engine.
27. Disconnect conducting sockets from the distributor of ignition, the coil of ignition and the transistor power supply unit. Exempt a conducting sleeve from clips on a head of cylinders and take aside. Turn off bolts and remove all wires of connection with weight on a head of cylinders and on the soaking-up collector.
28. Disconnect a cable of a speedometer and a wire from the check point.
29. Fix таль the elevator on eyes of a head of cylinders, pull таль that it apprehended the weight of the power unit.
30. Designate the provision of a coupling bolt (it is specified by an arrow) on an arm of a forward support of the power unit, turn off a nut of a coupling bolt and get a bolt.
31. Turn off a nut and get a coupling bolt of a back support (it is specified by an arrow). Remove a forward support and an arm.
32. Remove the right support and rubber pillows.
33. Remove the left support and rubber pillows.
34. Make sure that all details, wires and hoses which can interfere with dismantle are disconnected, removed and taken aside.
35. Drive the cart under the engine and carefully lower the power unit. It is expedient to carry out this operation with the assistant as it will be required to incline a little the engine not to touch a body.
36. Roll out the power unit from under the car.

Removal of transmission from the engine

PERFORMANCE ORDER
1. Fix the removed power unit wooden whetstones, having put it on the flat platform.
2. Remove a starter.
3. Uncover the pallet and turn off the first available bolt of the hydrotransformer, then turning the crankshaft, turn off serially other 3 bolts.
4. Fix the hydrotransformer by a piece of a metal strip, having tightened a strip a bolt to one of openings of fastening of a starter.
5. Turn off bolts of fastening of a case of transmission to the engine, having designated their arrangement.
6. Carefully remove transmission.

Installation

PERFORMANCE ORDER
1. If the check point acted from the engine, then execute the operations described below in subitem 1-6. If the check point did not act, then be guided by item 7 and further.
2. Measure distance from openings under bolts of fastening of the hydrotransformer to the demountable plane of a case of transmission which at the correct installation has to be not less than 21,1 mm.
3. Establish pins (if were removed).
4. Carefully install transmission on the engine on the directing pins and tighten bolts with the set moment.
5. Remove the strip fixing the hydrotransformer, combine hydrotransformer openings with openings in a drive plate and wrap fastening bolts.
6. Tighten hydrotransformer bolts with the set moment, establish a pallet cover, tighten bolts.
7. Establish a starter.
8. Place the power unit under the car and attach таль the elevator.
9. Working with the assistant, carefully power unit in a motor compartment.
10. Establish rubber pillows on an arm of the left support of the power unit, having tracked that hairpins of pillows entered arm openings. Establish into place a support, wrap bolts of fastening of a support to transmission and tighten them with the set moment. Insert a coupling bolt and tighten a nut by hand.
11. Establish rubber pillows on the right arm of a suspension bracket from a body, having convinced that hairpins of pillows entered openings in an arm. Establish a support on an arm and tighten bolts with the set moment. Insert a coupling bolt and tighten a nut by hand.
12. Insert a coupling bolt of a back support and tighten a nut by hand.
13. Establish a longeron, tighten bolts with the set moment.
14. Establish an arm of a forward support and tighten bolts. Insert a coupling bolt and tighten a nut by hand. Expose the engine so that the tags of a coupling bolt put when dismantling were combined and tighten a nut.
15. Shake the power unit and tighten coupling bolts of other support.
16. Further installation of the power unit is carried out upside-down.
17. Make sure that conducting is laid on former routes and is fixed by clips and brackets and that all sockets are attached.
18. Replace epiploons of half shafts and establish half shafts.
19. Attach all hoses of the cooling system.
20. Adjust a cable of the drive of a butterfly valve (see subsection 6.1.7).
21. Attach and adjust cables of the choice of transfers and kick - down - the mode.
22. Establish and adjust drive belts.
23. Replace oil in the engine and the check point.
24. Fill in cooling liquid.
25. Start the engine and be convinced of lack of leaks.


3.1.2.4. The power unit from the manual transmission

3.1.2.6. Head of the block of cylinders