Service of Nissan Sunny from 1991 to 1997 release in n-14 body.
1. Maintenance instruction
2. Maintenance
3. Engines
4. Cooling system
5. System of heating and ventilation
6. Fuel and exhaust system
6.1. Carburetor engines
6.2. Engines with system of injection of fuel
6.2.1. Specifications
6.2.2. Air filter
6.2.3. Cable of the drive of a butterfly valve
6.2.4. Pedal of management of a butterfly valve
6.2.5. Fuel
6.2.6. System of injection of fuel
6.2.7. Decompression of fuel system
6.2.8. Fuel pump
6.2.9. Fuel level sensor
6.2.10. Fuel tank
6.2.11. System of injection of fuel
6.2.12. Case of a butterfly valve
6.2.13. Units of system of injection of fuel
6.2.14. The soaking-up collector
6.2.15. Final collector
6.2.16. Exhaust system
6.3. System of food / production of the fulfilled gases
6.4. System of decrease in toxicity of the fulfilled gases
7. System of launch of the engine
8. Coupling
9. Transmissions
10. Half shafts
11. Brakes
12. Suspension brackets and steering
13. Body
14. Electric equipment
 


6-2-16-vykhlopnaya-sistema.html

6.2.16. Exhaust system

On cars without converter the exhaust system consists of 3 sections – a reception pipe, intermediate section with the resonator and terminal section with the muffler.

On cars with converter the exhaust system consists of 4 sections – the same 3 sections and section of converter. On a part of cars two converters, one of which is docked to a collector, are established.

On all length of a pipe of the exhaust system are suspended on rubber support, pipes are connected by flanges.

Removal

Each of sections can be dismantled irrespective of the others. It is also possible to remove all system at once.

PERFORMANCE ORDER
1. Lift the car and establish on supports (or come around on a hole or a platform).
Reception pipe
2. On cars with converter disconnect the socket from the sensor of exhaust gases. Get conducting from brackets.
3. Turn off fastening nuts to a collector and a fastening bolt to an arm, disconnect a pipe from a collector, remove laying.
4. Investigate flange connection with intermediate section and remove a pipe and laying.
Converter (on a part of cars)
5. Turn off two nuts and two bolts of fastening of a flange of a reception pipe to converter.
6. Turn off two bolts of fastening of an intermediate pipe to converter.
7. Disconnect converter from a reception pipe and remove.
8. Remove laying.
Intermediate pipe
9. On cars with converter turn off two bolts of fastening of an intermediate pipe to converter and remove laying.
10. On cars without converter turn off two nuts and two bolts of fastening, remove springs and disconnect an intermediate pipe from a reception pipe. Remove laying.
11. On all cars turn off a bolt of a rubber pillow in a back part of an intermediate pipe.
12. Turn off two bolts of fastening of an intermediate pipe to a terminal pipe of the muffler.
13. Remove an intermediate pipe and laying.
Terminal section of the muffler
14. Turn off two bolts of fastening to an intermediate pipe.
15. Unhook extensions and remove section.
Removal of all system
16. On cars with converter disconnect the socket from the sensor of exhaust gases.
17. Turn off nuts of fastening of a reception pipe to a collector and a fastening bolt to an arm, disconnect a pipe from a collector, remove laying.
18. Working with the assistant, disconnect system from rubber pillows and remove from the car.
Thermal guards
19. Guards are established on a part of cars between a body and exhaust pipes and fasten nuts, bolts and brackets.

Installation

PERFORMANCE ORDER
1. Installation is carried out upside-down.
2. Before assembly replace laying and clear demountable surfaces.
3. Check a condition of pillows, if necessary replace.
4. Make sure that between pipes, sufficient gleams are available the bottom and details of suspension brackets.

6.2.15. Final collector
6.3. System of food / production of the fulfilled gases