Service of Nissan Sunny from 1991 to 1997 release in n-14 body.
1. Maintenance instruction
2. Maintenance
3. Engines
4. Cooling system
5. System of heating and ventilation
6. Fuel and exhaust system
6.1. Carburetor engines
6.2. Engines with system of injection of fuel
6.3. System of food / production of the fulfilled gases
6.4. System of decrease in toxicity of the fulfilled gases
6.4.1. Models with 1,4 and 1,6 liter engines
6.4.1.1. Check and replacement of units of systems of decrease in toxicity
6.4.1.1.1. System of ventilation of a case
6.4.1.1.2. System of catching of vapors of gasoline
6.4.1.1.3. System of recirculation
6.4.1.1.4. System of a dookisleniye of exhaust gases
6.4.1.2. Catalytic converter
6.4.2. Models with 1,6 and 2,0 liter engines
7. System of launch of the engine
8. Coupling
9. Transmissions
10. Half shafts
11. Brakes
12. Suspension brackets and steering
13. Body
14. Electric equipment
 







6-4-1-1-2-sistema-ulavlivaniya-parov-benzina.html

6.4.1.1.2. System of catching of vapors of gasoline

CARBURETTOR ENGINES

Check

PERFORMANCE ORDER
1. Disconnect hoses from a tank and the thermal vacuum distributive valve (TVR) and blow.
2. TVR will screw in the right part of the soaking-up collector. On the cold engine disconnect both hoses from TVR. Blow TVR, attaching an auxiliary hose to unions. Air has to pass through TVR only on the heated-up engine.
3. The tank is mounted in a back left part of a motor compartment.
4. Disconnect a hose And from a tee. On the working engine create depression on a hose, – at the same time turns of the engine have to increase slightly, leak in a hose should not be. Attach a hose into place.
5. Disconnect from the carburetor a hose With and blow on the working engine, – leak should not be. Attach a hose into place.
6. Air cleaner branch pipe. Disconnect from a collector a hose In, blow a hose and create depression in a hose on the idle engine, – leak should not be. Attach a hose into place.
7. If when checking on subitem 4-6 there is a negative result, then the tank should be replaced.

INJECTOR ENGINES

Check

PERFORMANCE ORDER
1. Disconnect all hoses from a tank and the solenoidal valve and blow. The tank is mounted in a back left part of a motor compartment. The valve is screwed in a back part of the soaking-up collector.
2. For check of a tank disconnect hoses and blow in the union A, – air should not pass. Through the union In air has to pass freely. Otherwise replace a tank.
3. For check remove the solenoidal valve.
4. Air has to pass freely only through the union A and C on the deenergized valve. If on the valve to give tension, then air has to pass only through the union A and B.
5. At negative results of check replace the valve.

TANK WITH THE ABSORBER

Tank with an absorber on injector engines


Replacement

PERFORMANCE ORDER
1. Designate the route of a proleganiye of each hose and an order of accession of hoses to a tank.
2. Weaken collars and disconnect hoses.
3. Get a tank from an arm.
4. Install a tank upside-down.

THERMAL VACUUM DISTRIBUTIVE VALVE (TBP)

Thermal vacuum distributive valve (carburetor engines)


The TVR-valve (it is specified by an arrow) is screwed in the soaking-up collector.

Replacement

Works are performed on the cold engine.

PERFORMANCE ORDER
1. Merge liquid to valve level, or prepare a cap.
2. Disconnect hoses from TVR.
3. Carefully turn out TVR from a collector, remove laying.
4. Establish TVR upside-down. Replace laying.

SOLENOIDAL VALVE

Replacement

PERFORMANCE ORDER
1. Remove an air duct.
2. Disconnect the battery from weight, disconnect the socket from the valve.
3. Designate an order of accession of hoses on the valve.
4. Weaken collars and disconnect hoses, get the valve.
5. Install the valve upside-down.


6.4.1.1.1. System of ventilation of a case

6.4.1.1.3. System of recirculation