Service of Nissan Sunny from 1991 to 1997 release in n-14 body.
1. Maintenance instruction
2. Maintenance
2.1. Specifications
2.2. Service through each 15000 km or 6 months
2.3. Service through each 30000 km or 12 months
2.3.1. Check and replacement of belts of the drive of auxiliary units
2.3.1.1. Conditioner compressor belt
2.3.1.2. Belt of the drive of the pump of the hydraulic booster
2.3.1.3. Generator drive belt
2.3.2. Replacement of the fuel filter
2.3.3. Replacement of spark plugs (the car without Catholic converter)
2.3.4. Check of operation of the gate of a temperature regulator of the air filter
2.3.5. Check of system of decrease in toxicity of the fulfilled gases
2.3.6. Check of the sensor of exhaust gases
2.3.7. Replacement of brake fluid
2.3.8. Check of a suspension bracket and steering
2.3.9. Check of covers of half shafts
2.3.10. Check of the exhaust system
2.3.11. Check of angles of installation of wheels
2.3.12. Shift of wheels
2.3.13. Check of blocks of back drum brakes
2.3.14. Check of a condition of seat belts
2.3.15. Lubricant of door loops and locks
2.3.16. Check of the car in road conditions
2.4. Service through each 60000 km or 2 years
2.5. Service through each 60000 km or 12 months
3. Engines
4. Cooling system
5. System of heating and ventilation
6. Fuel and exhaust system
7. System of launch of the engine
8. Coupling
9. Transmissions
10. Half shafts
11. Brakes
12. Suspension brackets and steering
13. Body
14. Electric equipment
 







2-3-1-1-remen-kompressora-kondicionera.html

2.3.1.1. Conditioner compressor belt

Removal

PERFORMANCE ORDER
1. Working under a forward part of the car, unscrew screws and remove a plastic guard under a wing to get access to a crankshaft pulley. For expansion of working space it is possible to remove also in addition an engine mudguard, having unscrewed screws.
2. Turn the crankshaft the face head dressed on a pulley bolt so that it was possible to examine belts (or a belt) on all length. Check existence on belts of cracks, traces of a podgoraniye or mechanical damages. Check also existence on a belt of glossy sites and stratifications. At detection of damages or wear tracks replace a belt.
3. Disconnect the battery from weight.
4. Release a nut of fastening of a natyazhitel of a belt to the engine.
5. Turn off an adjusting bolt, displace a roller of a natyazhitel from a belt, before its full easing and take off a belt from pulleys.

Installation

PERFORMANCE ORDER
1. If the new belt is established, then previously be convinced that its type in accuracy corresponds to type of replaced.
2. Put on a belt on pulleys.
3. Rotating an adjusting bolt, pull a belt.

Adjustment of a tension
PERFORMANCE ORDER
1. Working under a forward part of the car, unscrew screws and remove a plastic guard under a wing to get access to a crankshaft pulley. For expansion of working space it is possible to remove also in addition an engine mudguard, having unscrewed screws.
2. Turn the crankshaft the face head dressed on a pulley bolt so that it was possible to examine belts (or a belt) on all length. Check existence on belts of cracks, traces of a podgoraniye or mechanical damages. Check also existence on a belt of glossy sites and stratifications. At detection of damages or wear tracks replace a belt.
3. The correct tension of a belt allows to prolong the term of its service. Avoid an excessive tension of a belt, otherwise wear of bearings of the generator amplifies.
4. The tension of a belt is checked in deflection size in the middle between two pulleys in the top part of a contour of the belt drive. Under the influence of the set effort the deflection of a belt has to be within norm.
5. For adjustment of a tension release a nut of a roller of a natyazhitel and rotate an adjusting bolt before receiving a normal tension. After adjustment turn the crankshaft on two turns and again check a belt tension.
6. Upon termination of tighten a nut of a roller of a natyazhitel with the set moment and connect the battery to weight.
7. Establish the removed guards, a wheel and lower the car.



2.3.1. Check and replacement of belts of the drive of auxiliary units

2.3.1.2. Belt of the drive of the pump of the hydraulic booster