Service of Nissan Sunny from 1991 to 1997 release in n-14 body.
1. Maintenance instruction
2. Maintenance
3. Engines
4. Cooling system
5. System of heating and ventilation
6. Fuel and exhaust system
7. System of launch of the engine
8. Coupling
9. Transmissions
10. Half shafts
11. Brakes
11.1. Specifications
11.2. Hydraulic actuator of brakes
11.3. Tubes and hoses
11.4. Blocks
11.5. Brake disk
11.6. Drums
11.7. Support of a forward brake
11.8. Support of a back brake
11.9. Wheel cylinder
11:10. Main cylinder
11:11. Brake pedal
11:12. Vacuum amplifier of brakes
11:13. Amplifier of brakes and backpressure valve
11:14. Lever of the emergency brake
11:15. Cables of the emergency brake
11:16. Adjustment of the emergency brake
11:17. Braking signal switch
11:18. Switch of a lamp of the emergency brake
11:19. Anti-blocking system
12. Suspension brackets and steering
13. Body
14. Electric equipment
 







11-10-glavnyjj-cilindr.html

11:10. Main cylinder

Removal

PERFORMANCE ORDER
1. Turn off a stopper and remove liquid from a nutritious tank (or extort, having unscrewed the union on a wheel).
2. Disconnect wires from the liquid level sensor.
3. Clear the union on the main cylinder.
4. Designate the union that at assembly to attach on former places.
5. Turn off nuts of unions, carefully get tubes and muffle openings.
6. Immediately wipe the spilled liquid.
7. Turn off nuts and remove the main cylinder from the vacuum amplifier.
8. Remove laying from the cylinder.

Dismantling


Prevention

Before dismantling get ремкомплект to the cylinder of that type which is installed on your car.


PERFORMANCE ORDER
1. Remove a nutritious tank, get a tank sealant (if it is provided).
2. Unbend ears and remove a cap.
3. On cars with ABS system push the first piston a wooden mandrel and turn off a lock bolt.
4. Get a lock ring (if it is provided).
5. Get a washer, pistons, springs and plates from the cylinder, having remembered an order of their installation. If necessary push out the piston a stream of compressed air, having clamped the cylinder in a vice.
6. Carefully wash out all details in alcohol or brake fluid and immediately dry.
7. Check a condition of details, at detection of wear or damages replace. Keep in mind that in ремкомплект the main cylinder pistons with sealants enter, a sealant separately in the spare part are not delivered.
8. If on the cylinder and the piston there are teases, scratches or traces of corrosion, then replace the cylinder assembled.
9. Before assembly grease the piston, cuffs and the cylinder with brake fluid.
10. Install in the cylinder all details in a former order.
11. You enter the piston roundabouts not to damage a cuff.
12. Establish a washer on an end face of the first piston. On cars with ABS system the lock bolt has to coincide with a groove in the second piston.
13. On cars with ABS system squeeze pistons and wrap a lock bolt.
14. Squeeze pistons and fix by a new cap (it is delivered in a remkomplekta).
15. Bend cap ears.
16. Check a condition of sealants of a tank, if necessary replace.
17. Dress a sealant and install a tank.

Installation
PERFORMANCE ORDER
1. Wipe the surfaces of the cylinder and the vacuum amplifier and dress new laying.
2. Install the cylinder on the vacuum amplifier, having convinced. that the pusher of the amplifier enters the cylinder on the center.
3. Tighten nuts with the set moment.
4. Establish tubes on the put tags, turn and tighten the union.
5. Fill in liquid in a tank and remove air from a hydraulic actuator.
6. Before departure check work of brakes.



11.9. Wheel cylinder

11:11. Brake pedal