Service of Nissan Sunny from 1991 to 1997 release in n-14 body.
	1. Maintenance instruction
	2. Maintenance
	3. Engines
	4. Cooling system
	5. System of heating and ventilation
	6. Fuel and exhaust system
	7. System of launch of the engine
	8. Coupling
	9. Transmissions
	10. Half shafts
	11. Brakes
		11.1. Specifications
		11.2. Hydraulic actuator of brakes
		11.3. Tubes and hoses
		11.4. Blocks
		11.5. Brake disk
		11.6. Drums
		11.7. Support of a forward brake
		11.8. Support of a back brake
		11.9. Wheel cylinder
		11:10. Main cylinder
		11:11. Brake pedal
		11:12. Vacuum amplifier of brakes
		11:13. Amplifier of brakes and backpressure valve
		11:14. Lever of the emergency brake
		11:15. Cables of the emergency brake
		11:16. Adjustment of the emergency brake
		11:17. Braking signal switch
		11:18. Switch of a lamp of the emergency brake
		11:19. Anti-blocking system
	12. Suspension brackets and steering
	13. Body
	14. Electric equipment

plans cul

11-7-support-perednego-tormoza.html

11.7. Support of a forward brake

Removal

PERFORMANCE ORDER

1. Lift a forward part of the car and establish on supports.
2. Remove a wheel.
3. For decrease in losses of liquid densely wrap a stopper of a tank having laid a polyethylene film, or press hoses.
4. Clear the ring union of a hose and turn off a bolt.
5. Remove two laying.
6. Remove blocks.
7. Turn away the top finger of a support.
8. Remove a support.
9. If necessary it is possible to remove a support arm.

Dismantling

PERFORMANCE ORDER

1. Carefully clear a support.
2. Get fingers for heads of bolts which screw in fingers.
3. Remove rubber covers of fingers.
	4. Remove a lock ring and a cover of the cylinder.
	5. Take the piston, having given air from the pump to an union opening.
	6. A wooden stick get a cylinder sealant.
7. Wash out all details in pure brake fluid or alcohol.
8. All a sealant and covers are subject to obligatory replacement.
9. Check a condition of a support, especially carefully examine the piston and the internal surface of the cylinder, replace worn-out details. The support or an arm of a support separately in the spare part are not delivered.
10. Minor defects on the cylinder are eliminated with polishing with a small skin whereas the piston with the same defects is subject to obligatory replacement. It is forbidden to polish the piston.
11. Check a condition of carvings on support fingers, the side play of fingers in a support has to be absent.
12. Blow channels in a support.
13. Before assembly check purity of all details.
14. Dip a cylinder sealant into liquid and establish in a cylinder flute.
	15. Dress a cover edge in a cylinder flute, grease with brake fluid the piston and the cylinder, install the piston in the cylinder and dress the second edge of a cover on the piston.
16. Dress new covers on support fingers, before installation in a support grease fingers with brake fluid.

Installation

PERFORMANCE ORDER

1. Establish a support arm, tighten bolts.

2. Establish a support, grease a carving of a bolt of the top finger with the fixing structure and wrap a bolt with the set moment.

3. Establish blocks.

4. Check freedom of movement of a support in an arm.

5. Attach a hose, having established two laying and having tightened a bolt of the ring union.

6. Remove polyethylene laying from a tank stopper (or remove collars from hoses).

7. Remove air from a wheel brake hydraulic actuator (if integrity of other contours was not broken).

8. Press several times a brake pedal.

9. Establish a wheel, lower the car.