Service of Nissan Sunny from 1991 to 1997 release in n-14 body.
1. Maintenance instruction
2. Maintenance
3. Engines
4. Cooling system
5. System of heating and ventilation
6. Fuel and exhaust system
7. System of launch of the engine
8. Coupling
9. Transmissions
10. Half shafts
11. Brakes
12. Suspension brackets and steering
12.1. Specifications
12.2. Bearings of naves of forward wheels
12.3. Rack of a forward suspension bracket
12.4. Lower lever
12.5. Spherical support of the lower lever
12.6. Stabilizer of cross stability of a forward suspension bracket
12.7. Bearings of back wheels
12.8. Details of a back suspension bracket
12.9. Wheel
12:10. Switch of ignition and lock of blocking of a steering column
12:11. Steering column
12:12. Steering mechanism
12:13. Covers of steering transfer
12:14. Hydraulic actuator
12:15. Pump of the hydraulic booster
12:16. Tips of steering draft
13. Body
14. Electric equipment
 


12-2-podshipniki-stupic-perednikh-koles.html

12.2. Bearings of naves of forward wheels

Replacement

PERFORMANCE ORDER
1. Lift a forward part of the car and establish on supports.
2. Remove a wheel.
3. Remove a disk and a support.
4. Remove the speed sensor (on cars with ABS system).
5. Turn off fastenings of an arm of conducting and take the sensor aside.
6. Disconnect a half shaft from only from a nave, take aside and fix (see subsection 10.2).
7. Turn off two nuts of fastening of a rack to a rotary fist (are specified by shooters), get bolts and disconnect a rack.
8. Rasshplintuyte also turn off nuts, a vypressuyta a spherical support and a tip of steering draft from fist eyes.
9. Vypressuyte a nave from the bearing. On a nave there has to be one of internal holders of the bearing.
10. Press a bearing holder from a nave.
11. Get an external epiploon.
12. Get an internal epiploon.
13. Get from an opening in a fist under the bearing a lock ring.
14. If landing of the remained holder weakened, then get a holder.
15. Vypressuyte the bearing from a fist a mandrel of suitable diameter which rests only against an external part of the bearing.
16. At a vypressovka it is necessary to rest a back part of a fist.
17. It is possible to Vypressovat the bearing also blows to the inserted internal holder through a tubular mandrel.

Installation

PERFORMANCE ORDER
1. Before installation of the new bearing carefully clear the internal surface of a fist.
2. Press an external holder of the bearing, resting a mandrel only against an external edge. It is forbidden to grease an external part of a holder for simplification of a press fitting.
3. Insert into a flute in a fist opening a lock ring.
4. Put lubricant in a cavity of an epiploon and carefully press an epiploon from the outer side of a rotary fist.
5. Establish a prop of an external part of a fist.
6. Put lubricant in an epiploon and press an epiploon from the inside of a fist.
7. Having reliably rested an internal holder of the bearing, carefully press a nave in a fist.
8. Check freedom of rotation of a nave.
9. Attach a half shaft and tighten a nut with the set moment.
10. Dress a disk and a support of a brake.
11. Attach a spherical support of the lower lever, wrap a new nut and tighten with the set moment.
12. Zashplintuyte nut new forelock.
13. Attach a rack, having replaced bolts and nuts.
14. Tighten bolts and nuts with the set moment.
15. Attach steering draft, having replaced a nut and the forelock.
16. Establish a wheel and lower the car.

12.1. Specifications
12.3. Rack of a forward suspension bracket