Service of Nissan Sunny from 1991 to 1997 release in n-14 body.
1. Maintenance instruction
2. Maintenance
3. Engines
3.1. 1,4 and 1,6 liters petrol engine
3.1.1. Types of repair of the engine without dismantle from the car
3.1.1.1. Specifications
3.1.1.2. Compression
3.1.1.3. Order of installation of the piston of the 1st cylinder in compression step VMT
3.1.1.4. Cover of a head of the block of cylinders
3.1.1.5. Crankshaft pulley
3.1.1.6. Cover of the chain drive of cam-shafts
3.1.1.7. Chains of the drive of cam-shafts
3.1.1.8. Natyazhiteli and uspokoitel of a chain, drive asterisk
3.1.1.9. Gaps in the mechanism of the drive of valves
3.1.1.10. Cam-shafts and pushers
3.1.1.11. Head of the block of cylinders
3.1.1.12. Oil pallet
3.1.1.13. Oil pump
3.1.1.14. Crankshaft epiploons
3.1.1.15. Flywheel
3.1.1.16. Engine mount details
3.1.2. Dismantle and capital repairs of the engine
3.2. 2,0 liters petrol engine
3.3. Diesel engine
4. Cooling system
5. System of heating and ventilation
6. Fuel and exhaust system
7. System of launch of the engine
8. Coupling
9. Transmissions
10. Half shafts
11. Brakes
12. Suspension brackets and steering
13. Body
14. Electric equipment
 


3-1-1-12-maslyanyjj-poddon.html

3.1.1.12. Oil pallet


Putting sealant on the pallet plane

 1. Flute

2. Opening

3. Inside

Removal

PERFORMANCE ORDER
1. Put the car on the emergency brake, then lift a forward part of the car and establish on supports. Disconnect the battery from weight.
2. Unscrew screws and remove a plastic guard under the engine.
3. Merge oil from the engine.
4. Disconnect a reception pipe of the muffler.
5. Turn off bolts and remove the small props connecting the check point to the block of cylinders on both sides of the engine (shooters specified places of fastening of a forward prop).
6. Turn off bolts and nuts of the oil pallet.
7. Open with blows of a palm consolidation of the pallet, lower the pallet and get from under the car.
8. Turn off two bolts and remove an oil receiver with the filter of rough cleaning and ring laying.
9. Wash out the filter of rough cleaning in solvent and check existence of contaminations or damages. At any signs of damages replace an oil receiver assembled with the filter.

Installation

PERFORMANCE ORDER
1. Clear the demountable planes of the pallet and block of cylinders of the consolidation remains, then wipe absolutely the pallet and the internal surfaces of the engine.
2. In a flute of an oil receiver lay new ring laying (it is specified by an arrow), establish an oil receiver and tighten bolts.
3. Clear the demountable planes and apply sealant on the flute stamped on the center of the condensed surface of the pallet between openings and also from that party of openings under bolts which is turned inside (see rice. Putting sealant on the pallet plane).
4. Install the pallet on hairpins, tighten nuts and bolts with the set moment.
5. Establish check point props, tighten bolts.
6. Establish a reception pipe of the muffler.
7. Establish plastic guards under the engine.
8. Fill in fresh oil in the engine, replace the filter.

3.1.1.11. Head of the block of cylinders
3.1.1.13. Oil pump