Service of Nissan Sunny from 1991 to 1997 release in n-14 body.
	1. Maintenance instruction
	2. Maintenance
	3. Engines
		3.1. 1,4 and 1,6 liters petrol engine
			3.1.1. Types of repair of the engine without dismantle from the car
				3.1.1.1. Specifications
				3.1.1.2. Compression
				3.1.1.3. Order of installation of the piston of the 1st cylinder in compression step VMT
				3.1.1.4. Cover of a head of the block of cylinders
				3.1.1.5. Crankshaft pulley
				3.1.1.6. Cover of the chain drive of cam-shafts
				3.1.1.7. Chains of the drive of cam-shafts
				3.1.1.8. Natyazhiteli and uspokoitel of a chain, drive asterisk
				3.1.1.9. Gaps in the mechanism of the drive of valves
				3.1.1.10. Cam-shafts and pushers
				3.1.1.11. Head of the block of cylinders
				3.1.1.12. Oil pallet
				3.1.1.13. Oil pump
				3.1.1.14. Crankshaft epiploons
				3.1.1.15. Flywheel
				3.1.1.16. Engine mount details
			3.1.2. Dismantle and capital repairs of the engine
		3.2. 2,0 liters petrol engine
		3.3. Diesel engine
	4. Cooling system
	5. System of heating and ventilation
	6. Fuel and exhaust system
	7. System of launch of the engine
	8. Coupling
	9. Transmissions
	10. Half shafts
	11. Brakes
	12. Suspension brackets and steering
	13. Body
	14. Electric equipment

3-1-1-4-kryshka-golovki-bloka-cilindrov.html

3.1.1.4. Cover of a head of the block of cylinders

Sequence of an inhaling of bolts of a cover of a head of cylinders

Removal

PERFORMANCE ORDER

1. Disconnect from wire candles, get wires from brackets on a cover of a head of cylinders.
	2. Weaken collars and disconnect hoses of a suction of intra crankcase gases in on a cover of a head of cylinders.
3. As it should be the return specified rice. The sequence of an inhaling of bolts of a cover of a head of cylinders, turn off bolts of fastening of a cover of a head of cylinders, get bolts and washers.
4. Lift a cover of a head of cylinders, get rubber laying from a flute in a cover and sealing rings of candles from openings under candles. On engines of early release also get the rubber caps inserted into semicircular deepenings in the right wall of a head of cylinders. On engines of later release these caps are executed with laying of a cover of a head of cylinders at the same time.
5. Check a condition of all rubber sealants of a cover, if necessary replace.

Installation

PERFORMANCE ORDER

1. Carefully clear the condensed surfaces of a cover and a head of cylinders, remove oil traces.
	2. Apply sealant on semicircular selections of a head of cylinders. On engines of early release lay in selections both semicircular caps so that a flat part of caps was aflush with the plane of a head of cylinders.
	3. Lay laying in a flute on a cover, having tracked correctness of its situation on all length.
	4. Establish sealing rings of spark plugs. If necessary record a sealant, having greased with a thin layer of sealant.
	5. Apply sealant on laying approximately in 1 cm on both sides from edges of semicircular selection under a cover of a back basic neck of a cam-shaft.
	6. Carefully establish a cover of a head of cylinders into place, at the same time the shift of rubber sealants of a cover is not allowed.
	7. Be convinced of correctness of installation of a cover, wrap bolts with washers. Tighten cover bolts in the specified sequence with the set moment.
8. Attach hoses to a cover.
9. Attach wires to spark plugs and insert wires into brackets.