Service of Nissan Sunny from 1991 to 1997 release in n-14 body.
	1. Maintenance instruction
	2. Maintenance
	3. Engines
		3.1. 1,4 and 1,6 liters petrol engine
		3.2. 2,0 liters petrol engine
		3.3. Diesel engine
			3.3.1. Technical characteristics
			3.3.2. Gear belt
			3.3.3. Replacement of laying of a head of cylinders
			3.3.4. Valves
			3.3.5. Replacement of maslootrazhatelny caps of a core of the valve
			3.3.6. Check of the directing valves
			3.3.7. Grinding in of a saddle of the valve
			3.3.8. Processing of a head of cylinders / valves
			3.3.9. Check / adjustment of gaps of valves
			3.3.10. Check of a compression
			3.3.11. Maple belt
			3.3.12. Malfunctions of the engine
			3.3.13. Engine lubrication system
			3.3.14. Oil contour
			3.3.15. Removal and installation of the pallet of a case
			3.3.16. Oil pump
			3.3.17. Cooling system
			3.3.18. Injection device
			3.3.19. Spark plugs
			3.3.20. Power supply system
			3.3.21. Check / replacement of the valve of interruption in supply of fuel
			3.3.22. Speed of idling and maximum speed
			3.3.23. Nozzles
			3.3.24. Beginning of giving of the fuel pump of high pressure
			3.3.25. Operation during the winter period
			3.3.26. Specifications of a power supply system of the diesel
			3.3.27. Useful tips for owners of the diesel car
	4. Cooling system
	5. System of heating and ventilation
	6. Fuel and exhaust system
	7. System of launch of the engine
	8. Coupling
	9. Transmissions
	10. Half shafts
	11. Brakes
	12. Suspension brackets and steering
	13. Body
	14. Electric equipment

3-3-11-klinovyjj-remen.html

3.3.11. Maple belt

Belt arrangement

1. The adjusting screw (for a maple belt of a servonasos)
2. A lock nut of 10 N. of m (for the adjusting screw of a servonasos, the moment zatyazhki:25 N. of m)
3. Cooling system pump pulley
4. Сервонасос (amplifier of steering)
5. Generator
6. The compressor (for the conditioner)
7. Intermediate pulley

8. Crankshaft pulley
9. A lock nut, 30 N. of m (for an intermediate pulley)
10. The adjusting screw (for a maple compressor belt of the conditioner)
11. A lock nut, 20 N. of m (for the adjusting screw of the generator, the inhaling moment: 25 N. of m)
12. The adjusting screw (for a maple belt of the generator)

If the former belt is established, then it should be checked for wear and damages. If its sidewalls obtrepatsya, there are cracks and places of gaps, maple the belt should be replaced anyway. At installation of a belt you watch that it correctly adjoined to all pulleys.

Check of a tension of a maple belt

To check a tension of a maple belt always at the cold engine.

PERFORMANCE ORDER

1. Press a belt a thumb from above between pulleys (see. "Black tags" on rice. Belt arrangement).

2. Measure the size of breakdown and compare to control value. At the same time press on a belt with a force of 100 N (10 kg). It corresponds to approximately strong pressing by a thumb. If necessary delay a belt a spring dynamometer down.

3. If control value is exceeded, pull a belt.

Replacement of a maple belt

PERFORMANCE ORDER

1. Weaken a lock nut.

2. Turn the adjusting screw until the belt can be taken off.

3. Take off maple a belt.

4. Impose a new maple belt and adjust a bolt on a certain value of a tension.

5. Put the lock clamp.

Condition of a maple belt	Being in the use		New
Maple belt for	Control value	Adjusting value	Adjusting value
The cooling system pump with servonasosy	8 mm	5 – 7 mm	4 – 6 mm
The cooling system pump without servonasos	8 mm	8 mm	6 mm
Conditioner compressor	17 mm	11 – 13 mm	9 – 11 mm
Generator	17 mm	10 – 12 mm	8 – 10 mm

3.3.10. Check of a compression

3.3.12. Malfunctions of the engine