|
3-3-15-snyatie-i-ustanovka-poddona-kartera.html
3.3.15. Removal and installation of the pallet of a caseFor consolidation of the pallet of a case usual sealant, for example, of Loctite is used.
Prevention
You do not apply too much sealant, be especially careful near openings of bolts. Details have to be gathered within 5 minutes after putting sealant. After the expiration of this time sealant has to be removed and applied anew.
Removal
| PERFORMANCE ORDER |
| 1. Disconnect a weight cable from the battery. |
Prevention
At the same time electronic memory, for example, of the store of malfunctions of the engine or a radio receiver code is erased. Before shutdown of the battery it is necessary to read
instructions in subsection 7.2.
|
| 2. Lift the car. |
| 3. Remove protection of the bottom of the engine. |
| 4. Merge engine oil. |
| 5. Remove the central beam. |
| 6. Remove a reception pipe of the muffler. |
| 7. Unscrew bolts of fastening of the pallet of a case. |
|
8. Hammer a wedge into consolidation between the block of cylinders and the pallet (shooters specified an arrangement of sealants). In workshops KV-10111100 adaptation which is driven in between the block of cylinders and the pallet of a case is for this purpose used. |
| 9. If there is no adaptation, it is possible to use an old knife. Carefully drive in a knife with the hammer between the block and the pallet. |
Prevention
Do not hook the pallet the screw-driver or a chisel at all, without having cut previously consolidation. At removal you watch that the uplotnitlny surface of the pallet of a case was not damaged.
|
| 10. Remove the case pallet. |
| 11. It is recommended to remove the mesh filter at the removed pallet and to clear the filter it in a cold cleaner. |
| 12. Check a grid for damages, for example, gaps, if necessary replace. |
|
Installation
| PERFORMANCE ORDER |
|
1. Carefully clear the sealing surfaces of the pallet and block of the consolidation remains by means of a triangular shaber and an edge of the razor. |
| 2. Accurately wipe the block, the mechanism of the crankshaft and the oil pump. Otherwise oil will flow down on consolidation of the pallet. |
| 3. Screw the mesh filter with new laying with 20 N.' effort of m. |
| 4. Degrease and dry up the interfaced surfaces of the pallet and the block of cylinders. As a cleaner it is possible to use alcohol or acetone. |
Prevention
It is impossible to use the cleaners corroding a varnish surface.
|
| 5. Enclose new laying in both semicircular dredging of the pallet of a case and on the ends from two parties cover with sealing means. |
|
6. Apply sealant with a strip 4-5 mm wide on all perimeter of a sealing surface of the oil pallet. At the same time impose a sealant strip between openings of bolts in a flute (1) of the pallet. On openings of bolts (2) impose a sealant strip on pallet inside at distance of 7 mm. |
|
7. Install the case pallet on the block of cylinders. Wrap bolts at first a hand, then cross-wise (with 1 on 15) with 8 N.' effort of m. |
Prevention
Wait before filling of oil of 30 minutes that sealant stiffened.
|
| 8. Establish a reception pipe of the muffler. |
| 9. Establish the central beam. |
| 10. Establish protection of the bottom of the engine. |
| 11. Lower the car. |
| 12. Fill in engine oil. |
| 13. Connect a cable of mass of the battery. |
| 14. If is, determine time on hours and enter a protective code of the radio receiver. |
| 15. Make a trial trip, check the level of oil and tightness of consolidation of the pallet of a case, in case of need, carefully tighten all bolts. |
|
| |