Service of Nissan Sunny from 1991 to 1997 release in n-14 body.
	1. Maintenance instruction
	2. Maintenance
	3. Engines
	4. Cooling system
	5. System of heating and ventilation
	6. Fuel and exhaust system
		6.1. Carburetor engines
		6.2. Engines with system of injection of fuel
		6.3. System of food / production of the fulfilled gases
			6.3.1. Models with single-point electronic injection of fuel
			6.3.2. Models with multipoint electronic injection of fuel
				6.3.2.1. Technical characteristics
				6.3.2.2. Air filter
				6.3.2.3. Accelerator rope
				6.3.2.4. Accelerator pedal
				6.3.2.5. System of injection of fuel
				6.3.2.6. Fuel system
				6.3.2.7. Fuel pump
				6.3.2.8. Fuel level sensor
				6.3.2.9. Fuel tank
				6.3.2.10. Case of a butterfly valve
				6.3.2.11. Elements of system of injection of fuel (1,6 l engines)
					6.3.2.11.1. Fuel collector and fuel injectors
					6.3.2.11.2. Fuel pressure regulator
					6.3.2.11.3. Potentiometer of a butterfly valve
					6.3.2.11.4. Additional valve of air supply
					6.3.2.11.5. Air stream sensor
					6.3.2.11.6. Electromagnetic valve of bystry operation of the engine
					6.3.2.11.7. The temperature valve of the accelerated warming up of the engine
					6.3.2.11.8. Sensor of an angle of rotation of a bent shaft and transistor of power
					6.3.2.11.9. Sensor of temperature of cooling liquid
					6.3.2.11.10. Engine electronic control unit
					6.3.2.11.11. Switch of neutral transfer
					6.3.2.11.12. Switch of blocking of starters / lamps of a backing
					6.3.2.11.13. Relay of an electronic control unit of the engine and fuel pump
					6.3.2.11.14. The switch in system of strengthening of steering
					6.3.2.11.15. The switch in the air conditioning system
					6.3.2.11.16. Sensor of speed of the movement of the car
				6.3.2.12. Elements of system of injection of fuel (2,0 l engines)
				6.3.2.13. Inlet collector
		6.4. System of decrease in toxicity of the fulfilled gases
	7. System of launch of the engine
	8. Coupling
	9. Transmissions
	10. Half shafts
	11. Brakes
	12. Suspension brackets and steering
	13. Body
	14. Electric equipment

6-3-2-11-3-potenciometr-drosselnojj-zaslonki.html

6.3.2.11.3. Potentiometer of a butterfly valve

Removal

PERFORMANCE ORDER

	1. The potentiometer of a butterfly valve (it is specified by an arrow) is installed on the right side of the case of a butterfly valve. Before its removal, disconnect a wire of the negative plug of the accumulator.
2. Disconnect the socket of connection of a potentiometer of a butterfly valve.
3. By means of white paint or a marker make marks in the case of a butterfly valve and a potentiometer.
4. Turn off two fixing screws and remove a potentiometer.
5. At installation, install a potentiometer on the case of a butterfly valve so that its lever was correctly installed on the lever of an axis of a butterfly valve.
6. Establish a fixing plate, then, combine the marks made before removal and twirl fixing screws a little. Adjust a potentiometer as follows.
7. By means of the tester established on measurement of resistance check that resistance of a potentiometer was such as it is specified in the section of technical characteristics (see subsection 6.3.2.1). If it is necessary, turn off fixing screws and turn a potentiometer that its resistance was such as it is specified in the section of technical characteristics.
8. When the potentiometer is correctly established, reliably tighten fixing screws, and connect the connection socket.
9. Connect a wire of the negative plug of the accumulator.

6.3.2.11.2. Fuel pressure regulator

6.3.2.11.4. Additional valve of air supply