Service of Nissan Sunny from 1991 to 1997 release in n-14 body.
1. Maintenance instruction
2. Maintenance
3. Engines
4. Cooling system
5. System of heating and ventilation
6. Fuel and exhaust system
6.1. Carburetor engines
6.2. Engines with system of injection of fuel
6.3. System of food / production of the fulfilled gases
6.3.1. Models with single-point electronic injection of fuel
6.3.2. Models with multipoint electronic injection of fuel
6.3.2.1. Technical characteristics
6.3.2.2. Air filter
6.3.2.3. Accelerator rope
6.3.2.4. Accelerator pedal
6.3.2.5. System of injection of fuel
6.3.2.6. Fuel system
6.3.2.7. Fuel pump
6.3.2.8. Fuel level sensor
6.3.2.9. Fuel tank
6.3.2.10. Case of a butterfly valve
6.3.2.11. Elements of system of injection of fuel (1,6 l engines)
6.3.2.11.1. Fuel collector and fuel injectors
6.3.2.11.2. Fuel pressure regulator
6.3.2.11.3. Potentiometer of a butterfly valve
6.3.2.11.4. Additional valve of air supply
6.3.2.11.5. Air stream sensor
6.3.2.11.6. Electromagnetic valve of bystry operation of the engine
6.3.2.11.7. The temperature valve of the accelerated warming up of the engine
6.3.2.11.8. Sensor of an angle of rotation of a bent shaft and transistor of power
6.3.2.11.9. Sensor of temperature of cooling liquid
6.3.2.11.10. Engine electronic control unit
6.3.2.11.11. Switch of neutral transfer
6.3.2.11.12. Switch of blocking of starters / lamps of a backing
6.3.2.11.13. Relay of an electronic control unit of the engine and fuel pump
6.3.2.11.14. The switch in system of strengthening of steering
6.3.2.11.15. The switch in the air conditioning system
6.3.2.11.16. Sensor of speed of the movement of the car
6.3.2.12. Elements of system of injection of fuel (2,0 l engines)
6.3.2.13. Inlet collector
6.4. System of decrease in toxicity of the fulfilled gases
7. System of launch of the engine
8. Coupling
9. Transmissions
10. Half shafts
11. Brakes
12. Suspension brackets and steering
13. Body
14. Electric equipment
 


6-3-2-11-6-ehlektromagnitnyjj-klapan-bystrojj-raboty-dvigatelya.html

6.3.2.11.6. Electromagnetic valve of bystry operation of the engine

The electromagnetic valve of increase in speed of operation of the engine in the idling mode
The electromagnetic valve – is specified by an arrow.

The electromagnetic valve of bystry operation of the engine in the mode of idling is installed on the forward side of the case of a butterfly valve.

Before its removal, disconnect a wire of the negative plug of the accumulator.

If it is necessary, remove the air filter, being guided by the instructions provided in subsection 6.3.2.2 for improvement of access to the valve.

Removal and installation

PERFORMANCE ORDER
1. Disconnect the connection socket from the electromagnetic valve.
2. Unscrew the electromagnetic valve from the case of a butterfly valve, remove a plunger, a spring and a sealing washer.
3. Installation is carried out upside-down removals. At installation use a new sealing washer. Check that the plunger and a spring were correctly established.


6.3.2.11.5. Air stream sensor
6.3.2.11.7. The temperature valve of the accelerated warming up of the engine