Service of Nissan Sunny from 1991 to 1997 release in n-14 body.
1. Maintenance instruction
2. Maintenance
3. Engines
4. Cooling system
5. System of heating and ventilation
6. Fuel and exhaust system
6.1. Carburetor engines
6.2. Engines with system of injection of fuel
6.3. System of food / production of the fulfilled gases
6.3.1. Models with single-point electronic injection of fuel
6.3.1.1. Technical characteristics
6.3.1.2. Air filter
6.3.1.3. Accelerator rope
6.3.1.4. Accelerator pedal
6.3.1.5. The gasoline which is not containing tetraethyllead
6.3.1.6. System of injection of fuel
6.3.1.7. Fuel system
6.3.1.8. Fuel pump
6.3.1.9. Fuel level sensor
6.3.1.10. Fuel tank
6.3.1.11. Case of a butterfly valve
6.3.1.12. System of injection of fuel / ignition
6.3.1.13. Elements of system of injection of fuel
6.3.1.13.1. Fuel injector
6.3.1.13.2. Fuel pressure regulator
6.3.1.13.3. Additional valve of air supply
6.3.1.13.4. Potentiometer of a butterfly valve
6.3.1.13.5. Air stream sensor
6.3.1.13.6. Electromagnetic valve of bystry operation of the engine
6.3.1.13.7. The temperature valve of the accelerated warming up of the engine
6.3.1.13.8. Damper of a butterfly valve
6.3.1.13.9. Sensor of an angle of rotation of a bent shaft
6.3.1.13.10. Power transistor
6.3.1.13.11. Sensor of temperature of cooling liquid
6.3.1.13.12. Sensor of detonation combustion of fuel
6.3.1.13.13. Engine electronic control unit
6.3.1.13.14. Heater of fuel mix
6.3.1.13.15. Switch of neutral transfer
6.3.1.13.16. Switch of blocking of starters / lamps of a backing
6.3.1.13.17. Relay of an electronic control unit of the engine, heating of fuel mix and fuel pump
6.3.1.13.18. The switch in system of the hydraulic booster of steering
6.3.1.13.19. The switch in the air conditioning system
6.3.1.14. Inlet collector
6.3.2. Models with multipoint electronic injection of fuel
6.4. System of decrease in toxicity of the fulfilled gases
7. System of launch of the engine
8. Coupling
9. Transmissions
10. Half shafts
11. Brakes
12. Suspension brackets and steering
13. Body
14. Electric equipment
 


6-3-1-13-4-potenciometr-drosselnojj-zaslonki.html

6.3.1.13.4. Potentiometer of a butterfly valve


The potentiometer of a butterfly valve is installed on the right side of the case of a butterfly valve.

Removal and installation

PERFORMANCE ORDER
1. Before its removal, disconnect a wire of the negative plug of the accumulator.
2. Access to the regulator of pressure of fuel will be significantly improved if to remove the air filter (see subsection 6.3.1.2).
3. Disconnect the socket of connection of a potentiometer of a butterfly valve.
4. By means of white paint or a marker make marks in the case of a butterfly valve and a potentiometer.
5. Turn off and remove two fixing screws, then remove a fixing plate and a potentiometer.
6. At installation, install a potentiometer on the case of a butterfly valve so that its lever was correctly installed from above the lever of an axis of a butterfly valve.
7. Establish a fixing plate, then, combine the marks made before removal and twirl fixing screws a little.
8. Adjust a potentiometer. For this purpose by means of the tester established on measurement of resistance check that resistance of a potentiometer was such as it is specified in subsection 6.3.1.1.
9. If it is necessary, turn off fixing screws and turn a potentiometer.
10. When the potentiometer is correctly established, reliably tighten fixing screws and connect the connection socket.
11. Connect the accumulator and if it is necessary, install into place the air filter.

6.3.1.13.3. Additional valve of air supply
6.3.1.13.5. Air stream sensor