Service of Nissan Sunny from 1991 to 1997 release in n-14 body.
1. Maintenance instruction
2. Maintenance
3. Engines
4. Cooling system
5. System of heating and ventilation
6. Fuel and exhaust system
6.1. Carburetor engines
6.2. Engines with system of injection of fuel
6.3. System of food / production of the fulfilled gases
6.3.1. Models with single-point electronic injection of fuel
6.3.1.1. Technical characteristics
6.3.1.2. Air filter
6.3.1.3. Accelerator rope
6.3.1.4. Accelerator pedal
6.3.1.5. The gasoline which is not containing tetraethyllead
6.3.1.6. System of injection of fuel
6.3.1.7. Fuel system
6.3.1.8. Fuel pump
6.3.1.9. Fuel level sensor
6.3.1.10. Fuel tank
6.3.1.11. Case of a butterfly valve
6.3.1.12. System of injection of fuel / ignition
6.3.1.13. Elements of system of injection of fuel
6.3.1.13.1. Fuel injector
6.3.1.13.2. Fuel pressure regulator
6.3.1.13.3. Additional valve of air supply
6.3.1.13.4. Potentiometer of a butterfly valve
6.3.1.13.5. Air stream sensor
6.3.1.13.6. Electromagnetic valve of bystry operation of the engine
6.3.1.13.7. The temperature valve of the accelerated warming up of the engine
6.3.1.13.8. Damper of a butterfly valve
6.3.1.13.9. Sensor of an angle of rotation of a bent shaft
6.3.1.13.10. Power transistor
6.3.1.13.11. Sensor of temperature of cooling liquid
6.3.1.13.12. Sensor of detonation combustion of fuel
6.3.1.13.13. Engine electronic control unit
6.3.1.13.14. Heater of fuel mix
6.3.1.13.15. Switch of neutral transfer
6.3.1.13.16. Switch of blocking of starters / lamps of a backing
6.3.1.13.17. Relay of an electronic control unit of the engine, heating of fuel mix and fuel pump
6.3.1.13.18. The switch in system of the hydraulic booster of steering
6.3.1.13.19. The switch in the air conditioning system
6.3.1.14. Inlet collector
6.3.2. Models with multipoint electronic injection of fuel
6.4. System of decrease in toxicity of the fulfilled gases
7. System of launch of the engine
8. Coupling
9. Transmissions
10. Half shafts
11. Brakes
12. Suspension brackets and steering
13. Body
14. Electric equipment
 


6-3-1-13-7-temperaturnyjj-klapan-uskorennogo-progreva-dvigatelya.html

6.3.1.13.7. The temperature valve of the accelerated warming up of the engine


The temperature valve of the accelerated warming up of the engine is installed on the left side of the case of a butterfly valve, between the top and lower sections of the case.

Removal and installation

PERFORMANCE ORDER
1. Before its removal, disconnect a wire of the negative plug of the accumulator.
2. Remove the air filter (see subsection 6.3.1.2).
3. Turn a cam of the accelerated operation of the engine to disconnect it from the connecting mechanism of a butterfly valve.
4. Combine an opening in a cam with an opening in the case of a butterfly valve and record a cam in this situation, having inserted a drill or the probe with a diameter of 3 mm into openings.
5. Turn off fixing screws of the top section of the case of a butterfly valve, then, accurately remove the top section from the lower section.
6. Remove laying and you will throw out it; at installation it is necessary to use new.
7. Turn off two fixing screws and remove a fixing plate of the valve from the lower section of the case of a butterfly valve.
8. Get the valve from a nest and remove a sealing ring.
9. Installation is carried out upside-down removals.
10. At installation use a new sealing ring and laying between sections of the case of a butterfly valve.

6.3.1.13.6. Electromagnetic valve of bystry operation of the engine
6.3.1.13.8. Damper of a butterfly valve